Arroyo Instruments LaserSource 4200 Series Instrukcja Użytkownika

Page 10 · 4200 Series LaserSource User’s Manual Operation The Front Panel Operation of the LaserSource is very straightforward. The sections bel

4200 Series LaserSource User’s Manual · Page 11 When the unit is in remote mode, the yellow Remote LED will be lit. More information about how the i

Page 12 · 4200 Series LaserSource User’s Manual Shrt A short circuit has been detected on the output. OutT The unit is out-of-tolerance. See the

4200 Series LaserSource User’s Manual · Page 13 Menu Description Factory Default Im limit This setting controls the maximum amount of monitor pho

Page 14 · 4200 Series LaserSource User’s Manual Menu Description Factory Default On Delay The delay, from the time the Output button is pressed t

4200 Series LaserSource User’s Manual · Page 15 Control Modes The LaserSource offers five laser control modes: Io (ACC), Io HiBW (ACC), Im (AMC),

Page 16 · 4200 Series LaserSource User’s Manual Remote Mode Operation Remote mode operation is when the LaserSource is being controlled by a comp

4200 Series LaserSource User’s Manual · Page 17 Rear Panel In addition to the input power connector described above, there are four connectors an

Page 18 · 4200 Series LaserSource User’s Manual reset to factory defaults. Calibration will not be affected, but all settings will be returned to th

4200 Series LaserSource User’s Manual · Page 19 Connecting to the LaserSource A laser diode is very sensitive to electro-static discharge (ESD),

Page 2 · 4200 Series LaserSource User’s Manual Introduction Thank you for choosing the LaserSource from Arroyo Instruments. Your LaserSource is a

Page 20 · 4200 Series LaserSource User’s Manual applications, part number 1221 is a two meter cable with a male DB-9 on one end and stripped and tin

4200 Series LaserSource User’s Manual · Page 21 Specifications Description Specifications LASER CURRENT (ACC) Range (mA) 0 – 100 0 – 500 0

Page 22 · 4200 Series LaserSource User’s Manual Error Messages Error Code Description Cause E-100 General Error The error code is non-specific

4200 Series LaserSource User’s Manual · Page 23 E-510 Laser out of tolerance disabled output The laser output was turned off because an out-of-tole

Page 24 · 4200 Series LaserSource User’s Manual Maintenance and Service Maintenance The LaserSource requires no regular maintenance other than p

4200 Series LaserSource User’s Manual · Page 25 European Community Declaration of Conformity EC Declaration of Conformity I/We Arroyo Instru

Page 26 · 4200 Series LaserSource User’s Manual Notes:

4200 Series LaserSource User’s Manual · Page 27 Notes:

Copyright © 2006, Arroyo Instruments. All Rights Reserved. P/N 530-1000 Rev C Copyright © 2008, Arroyo Instruments. All Rights Reserved P/N 530-1

4200 Series LaserSource User’s Manual · Page 3 What’s in the Box Along with the LaserSource itself, a CD with electronic copies of this manual, th

Page 4 · 4200 Series LaserSource User’s Manual Safety Terms and Symbols The following safety-related terms are used in this manual: • Warnings

4200 Series LaserSource User’s Manual · Page 5 General Warnings WARNING To avoid electrical shock, ensure a 3-prong power cord is used, an

Page 6 · 4200 Series LaserSource User’s Manual Quick Start The LaserSource was designed with ease of use in mind, and you will likely have littl

4200 Series LaserSource User’s Manual · Page 7 Installation Installation of the LaserSource is very straightforward, as the quick start section a

Page 8 · 4200 Series LaserSource User’s Manual 100V Setting 120V Setting 230V Setting 240V Setting Reinsert the voltage selector and

4200 Series LaserSource User’s Manual · Page 9 Ventilation The LaserSource has vent holes on the rear and bottom of the unit. You must not block th